汇天成蓄电池
汇天成蓄电池
汇天成蓄电池
汇天成蓄电池特点:
1.维护简单
充电时，电池内部产生的氧气大部分被极板吸收还原成电解液，基本没有电解液减少。
2.持液性高
电解液被吸收于特殊的隔板中，保持不流动状态，所以即使倒下也可使用。（倒下超过90度以上不能使用）
3.安全性能卓越
由于极端过充电操作失误引起过多的气体可以放出，防止电池的破裂。
4.自放电极小
用特殊铅酸合金生产板栅，把自放电控制在。
5.寿命长、经济性好
电池的板栅采用耐腐蚀性好的特种铅钙合金，同时采用特殊隔板能保住电解液，再同时用强力压紧正板活性物质，防止脱落，所以是一种寿命长、经济的电池。
适用范围
太阳能蓄电池、UPS
汇天成主要追求产品的先进性，可靠性和环保性，采用国际内化成高新技术及生产工艺，实现了企业的环保理念。外化成和内化成区别在于：传统蓄电池主要通过化成槽进行充电，化成后变为熟极板，然后出槽，负极板在接触空气和清洗时会快速氧化，很难保证电池极板质量，并产生废水，对环境造成很大污染；内化成则采用特殊配方的生极板，装入电池槽内密封充电，极板既不会接触到空气也不会氧化，正负极板充电均衡，电池一直性好，寿命长，真正实现了优化生产，绿色电池的环保理念。汇天成蓄电池使用无污染排放的工艺标准，减少蓄电池的极板污染，同时产品质量也大大提高。
HTC mainly pursuits the products’ advanced, reliability and environmental protection, it adopted the inner production process, the advanced high-tech in International field, to achieve the its
environmental philosophy. The difference between the inner-production and outer-production is: the traditional battery mainly be charged through the production slot, then they changed into processed
plate and get out of the slot. The negative plate would be rapid oxidized when exposed to air and cleaned.It is difficult to ensure the quality of battery plates. And the produced wastewater would
cause great pollution to the environment. 产品特点Features 免维护无须补液 Maintenance free and without liquid added 适应温度广(-15-45℃) wide range of adaptation temperature (-15-45℃) 设计寿命长(5-8年) long design life
(5-8 years) 安全防爆 safety explosion-proof 无游离电解液，侧倒90°仍能使用 no free electrolyte and can be still useful when the side down of 90 ° 内阻小，大电流放电性能好 Small internal resistance and good performance of high
current discharge 自放电小 Small self-discharge 荷电出厂，使用方便 charged before they leave the factory and easy to use 独特配方，深放电恢复性能好 Unique formula and good performance of deep-discharge recovery 注意attention
额定容量(1C10小时率)为在25℃下所得的平均值，可以通过10次以上的充、放循环使用； Nominal capacity (1C10-hour rate) is obtained at 25℃on average, can accept more than 10 times of charge and discharge cycle use 安装使用 Installation and
Usage 使用前，请检查蓄电池外观(有无漏酸，破裂)。 Before use, check battery skin (with seamless acid, rupture). 蓄电池的安装必须由人员来进行。 The battery must be installed by professionals.
在电池连接过程中，请戴好防护手套，使用扭矩扳手等金属工具时，请将金属工具进行绝缘包装以防触电。禁止将金属工具同时接触到电池的正、负端子，造成电池短路。 In the course of the battery connection, wear protective gloves. When use a torque wrench and other metal tools, please
insulation packaging to prevent electric shock. Prohibit access metal tools to the battery positive and negative terminals at same time. Otherwise cause the battery short circuit.
安装搬运电池时应均匀受力，受力处应为蓄电池壳的部分，避免损伤极柱。 The battery should be uniform force when Installation and carrying the battery. Force at the shell should be part of the battery shell to avoid damage the pole.
禁止将不同品牌，不同容量的蓄电池并联或串联使用；电池在多只串联使用时，请按电池标识“+”，“-”极柱依次排列，电池之间的距离不能少于15mm,且连接部位要紧固，防止产生火花或接触不良。 Prohibit hybrid application of different brands and different capacity batteries in parallel or in series.
Please put the battery in order of priority identified "+","-" pole when in a a multi-series usage. The space between batteries can not be less than 15mm and the connection parts must be tightened to
prevent sparks or instable contact. 安装接插式端子的蓄电池时，请勿改变端子的形状和位置，如特殊情况需要，请与客户服务联系。 do not change the shape and location of terminals when Installing plug-in terminal of the battery. Please contact
customer service at special circumstances require. 和外接设备连接之前，必须使设备处于断开状态，并再次检查蓄电池的连接极性是否正确，然后再将蓄电池(组)的正极连接设备的正极，蓄电池(组)的负极连接设备的负极端子，并紧固好连接线。 The device must be disconnected and check again the correct
of battery polarity connection before connecting external devices. Then connect the positive cathode of the battery (group) to the positive cathode of devices, the negative anode to the negative
cathode devices terminal, and tighten the cable.
警告：
1.请不要让含有挥发油、香蕉水、汽油等有机溶剂、洗涤剂接触池壳及盖子。否则会引起电池壳开裂、细裂纹，导致漏酸。
2.蓄电池上禁止放扳手、钳子等金属工具。否则，有导致短路造成烧伤、蓄电池破损的危险。
3.在蓄电池的端子部分、连接导体及螺栓、螺母处正确安装绝缘盖，否则有触电的危险。如不正确安装，发生短路时，可能引发烧伤、蓄电池受损及引炸。
4.扭紧螺栓螺母时，请按规定的扭力来扭紧，否则有可能产生火花或端子受损